\u00a9 2021 wikiHow, Inc. All rights reserved. If all we wish to construct is a simple single-battery, single-resistor circuit, we may easily use alligator clip jumper wires like this: Jumper wires with “alligator” style spring clips at each end provide a safe and convenient method of electrically joining components together. ... Tin the wires from the battery by heating the wire with your iron and applying a bit of solder. Heat the wire end with the soldering iron for a few seconds and briefly touch the solder wire to the bare wire, just long enough to melt the solder, and let it flow into the stranded wires. Avoid using heat-shrink tubing that’s too large for the wire since you may not be able to secure it completely. Please consider supporting our work with a contribution to wikiHow. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. Wasn’t that simple? Paperclips work well as they’re steel so won’t become soldered to your piece, won’t melt and are much easier to form and This image may not be used by other entities without the express written consent of wikiHow, Inc.
\n<\/p>

\n<\/p><\/div>"}, pretty). Clean the area to be soldered, scraping the wire down to bare metal and then wiping it clean with alcohol or acetone. If a… The first part will deal with tools and equipment; the second part will demonstrate some techniques for you to consider.Warning! Dieting is the WORST. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Learn How to Solder Correctly. 4.6 out of 5 stars 4,024. Cover and waterproof the exposed wires to seal them and you’re finished! You can get alligator clips from your local hardware store. % of people told us that this article helped them. You can get wire strippers from your local hardware store. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Then add some solder until the wire is soaked with solder. Squeeze the handles together firmly together and pull the jaws toward the end of the wire to remove the insulation. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Warning: Don’t touch the solder directly to the soldering iron when you apply it to the wires since this creates a “cold solder,” which won’t as reliable of a connection and could cause a fuse to blow. Secure the jaws of a wire stripper 1 inch (2.5 cm) from the end of one of the wires you’re splicing together. Strip 1 in (2.5 cm) of the insulation off the end of each wire. Do the same to the pads where the wires are going to be soldered. By Mike Allen. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. Soldering wires requires a few extra techniques to be successful. Be sure to work in a well-ventilated area so the fumes from the solder don’t build up. Hold the two tinned wires on top of each other and touch the soldering iron to both wires. Position pre-tinned wire on solder dot and apply soldering iron to the wire until the solder melts. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. Tip: If you have stranded wires, you can also separate the individual strands and push the 2 wires together so the strands intermesh. Use nothing but 60-40 rosin-core solder intended for electrical wiring. When using a soldering iron, you must be careful and not touch the tip or else it will burn you when it is on. Soldering With Copper Wire Apply the tip of the soldering iron to the wet sponge to make the tip clean. Resistance Tinning Wire with Silver Solder 15. However, if soldering isn’t an option, you can use a conductive adhesive or wire glue. Don’t touch the end of the soldering iron while it’s hot since it can cause severe burns. Resistance soldering shall not be used on or near fuelled aircraft or in other hazardous locations. This process is known as “tinning” the iron and it stops oxidation, which can cause the iron to heat unevenly. {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/9\/90\/Solder-Wires-Together-Step-1-Version-2.jpg\/v4-460px-Solder-Wires-Together-Step-1-Version-2.jpg","bigUrl":"\/images\/thumb\/9\/90\/Solder-Wires-Together-Step-1-Version-2.jpg\/aid7332978-v4-728px-Solder-Wires-Together-Step-1-Version-2.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"